Eco Beauty — Private Label Hair Care Manufacturer
← All formulas
Professional Application Guide · HC012

NANO ONE NANOPLASTIA

Professional Nanoplastia combining fibre alignment with replenishing care. Helps reduce frizz and leave the hair softer, smoother and more luminous.

Key actives
CollagenHyaluronic acidAmino acids
Before you begin

For professional use only. Assess the hair's condition, thickness, porosity, elasticity and chemical history before every application. Perform a strand test using the intended protocol before treating the full head.

Processing time, rinsing, flat-iron temperature and number of passes must be selected according to the formula instructions, hair assessment and strand-test results. Hair type alone does not determine suitability.

Do not proceed if the test section shows breakage, excessive fragility or other adverse changes. Contact our technical educator for guidance.

Step-by-step protocol

  1. 1

    Step 1 — Cleanse

    Wash the hair thoroughly with shampoo. Select the cleansing approach according to the hair assessment and the formula's approved protocol.

  2. 2

    Step 2 — Dry completely

    Dry the hair completely before applying the smoothing formula.

    100% dry
  3. 3

    Step 3 — Section and apply

    Divide the hair into six sections and apply the product evenly, starting at the back. Distribute carefully through the lengths.

  4. 4

    Step 4 — Allow to process

    Leave the product on for the processing time below, according to the hair assessment and strand-test results. On easy-to-treat hair only (low resistance, good condition), NANO ONE can also follow a shorter express processing time, provided the strand test confirms the result. For all other hair, use the standard processing time.

    40 min fine hair · 60 min coarse hair
  5. 5

    Step 5 — Rinse

    Rinse with water, removing all of the product.

    Rinse 100%
  6. 6

    Step 6 — Dry completely again

    Blow-dry the hair completely before flat ironing.

    100% dry
  7. 7

    Step 7 — Flat iron

    Work through thin sections using the temperature and number of passes for this formula. Adjust within the approved protocol according to the hair's condition and strand-test results.

    230°C10–15 passes per thin section
  8. 8

    Step 8 — Complete the service

    After flat ironing, apply a hair mask and leave it on for 5 minutes. Rinse thoroughly. Apply conditioner and rinse again. Finish with a serum, then blow-dry or allow the hair to dry naturally.

Adapt the protocol to the hair

The following guide supports professional assessment. Always consider the hair's current condition and chemical history, and perform a strand test before every application. Use the parameters approved for the selected formula.

Max.= upper limit, not a target. Always confirm with a strand test.

Bleached / Blonde / Grey

Shampoo
Regular
Processing time
45 min
Rinsing
100%
Flat-iron
200 / 220 / 230°C — adjust
Passes
10–15

Colour-treated

permanent, demi or semi-permanent

Shampoo
Regular
Processing time
60 min
Rinsing
100%
Flat-iron
200 / 220 / 230°C — adjust
Passes
10–15

Fine / Delicate

Shampoo
Regular
Processing time
40 min
Rinsing
100%
Flat-iron
220 / 230°C — adjust
Passes
10–15

Virgin / Coarse / Resistant

Shampoo
Deep-cleansing
Processing time
60 min
Rinsing
100%
Flat-iron
Up to 250°CMax.
Passes
15–20Max.most resistant hair only

Normal / Wavy

Shampoo
Regular or deep-cleansing
Processing time
60 min
Rinsing
100%
Flat-iron
230°C — adjust
Passes
15–20

Always prioritise the hair's condition over its category. Maximum temperatures and pass counts are not targets. If the strand test shows adverse changes, do not proceed with the full application. Seek guidance from our technical educator.

Need help adapting the protocol?

Our technical educator can help you assess the hair, understand the application steps and select the appropriate protocol for your formula.

Talk to our technical educator

Your assigned Account Manager can also book a technical meeting with our educator.